Home » Softub

Softub Circuit Board,used, Fits All Digital Softubs - 140/220/300 Gallon

Location: 
United States, California, San Rafael
Ships to: 
United States, Canada
Current Price: 
 $225 
Quantity: 
1
Condition: 
Used
Listing Type: 
Chinese
Make: 
Softub
Model: 
Digital 140/220/300 gallon
Item's Postal Code: 
949**
Payment Methods: 
PayPal
Condition Description: 
Used, functions properly, tested on Softub and bench tested, 104 degree version
Description: 

Get your Softub running today with this used circuitboard, plug it in and go.... This has been tested and performs correctly with the DIGITAL top control panel. This is the 104 degree circuitboard. It does not have the programming to go to 106 degrees, nor the 12 hour sleep mode. It can replace any digital circuitboard, even the newer one. NO RETURNS, please do not buy this and then tell me it does not fit your Softub, contact me first if you are not sure, no try outs allowed.

FYI this was on Softubs from early 2000's until aprox 2010. It starts with default of 100 degrees, and will go up to 104 degrees. It will replace the newer version that shows a P when starting but it will not go up to 106 degrees. Returns are not accepted, please contact me with any questions about application you might have, there have been 3+ different circuitboards over the last 25 years. This one was used on many models, double check please!

Be certain your circuitboard is the problem please, hotwire the motor to see if it runs. Check voltage to the board, should be 110 volts. Check for power to the relays, 110V into the first relay and out to the second relay. When there is run signal(for heat or jets) the second relay engages and sends power to the motor. You can see which relay is which, follow wires, power in and power to the motor.

Relays are often the first problem, tap the side of them to see if they are stuck off or even stuck on sometimes.... Contact me with questions please, 15+ years of Softub repair and service experience, thanks, Dale

Returns Accepted: 
Not
A seller's positive feedback score: 
100.00%

Questions

Lawrence Ciardella - 07/08 12:36PM
I was told I needed a board by a hot tub repair company .. How can I buy this?
Dan - 31/08 1:52PM
Is this still available?
Gary Oswalt - 09/02 2:33AM
My hot tub was working fine then the motor went bad I got a replacement and it started fine. Then it started giving me a ip5 code and it keeps trying to cycle then it will eventually run for about 30 minutes and throw the code again.
John W Thomas - 08/03 6:14AM
I need one of these. Thank you.
Chris - 17/03 8:03PM
My softub is acting funny. The lcd screen will read 100 when I reset the guitar, but won't always allow me to change the temp. Usually after a few minutes, the lcd screen either shows 1 single number, such as 0, or 3 or it will rapidly flash a random single digit such as 0, 3, or 00. The pump turns on, the heater works and the jets work. But when the lcd screen goes awry, I can not get the jets to turn on or change the temperature. Does this sound like a circuit board issue?
JerryO - 02/05 5:16PM
Still available?
Michael - 09/10 2:59PM
Do you still have available?
Vaughn Nelson - 31/05 1:40PM
How do I purchase one circuit board.
Brad adams - 29/11 3:39PM
I need a board for a t300 softub. Its is short cycling the pump motor.
Sorah - 02/06 5:46AM
How do I purchase this?
Tom Hoerner - 15/11 8:30AM
I have a T-300 softub with a circuit board marked "C-2006". I've measured 110V coming in to the board and 110 volts out of the relay that has no wires connected to the top two terminals. I disconnected the single black wire that feeds the motor from the second relay to measure the voltage from that terminal of the second relay to common and measure less than 110 volts. What advice do you have for next steps? Thanks you, Tom
Jean - 24/08 3:25PM
I have a T-300 Softub manufactured in 2015. It is short-cycling the motor. The tub heats the water, the motor runs and the jets run, but the constant cycling is unacceptable. What needs repaired/replaced?

Add new question to the seller