Hot Tub Heater Control Digital Spa Controller Pack C5 United Spas CBT7 & 5 Cords

NEW spa control system, complete, by United Spas, model C5/CBT7, controls 2 speed main pump and air blower, plus light, and receptacle for an ozonator too, with pump power cord, blower cord, light cord, users manual, and digital topside display. A very nice replacement control works on most any hot tub or portable spa, replacing your old control and heater. Includes stainless steel high flow 5kw heater, 15" long, standard size. The listing includes economy ground shipping to lower 48 states. A very complete kit with topside and 5 cords for pump, blower, topside, temp sensor, and light.

As shipped runs a 2-speed pump, and air blower (or second pump) and a light. Optional cords allow other devices to be run, just message us BEFORE you buy for a quote on your requested options. Note on temp sensor cord, if you message us right at the time you buy, we can provide a short built in temp sensor already attached to the heater instead of the 8 foot cord and temp sensor. This makes the unit fully self-contained, so you won't have to locate the temp sensor yourself, saves time! Message us though, please.

Additional detail: -This CBT7 Control comes with 5kw 15" high flow heater, 2.5x5.0" Topside display/keypad, pump and blower and light cords, and is a complete unit to replace your old spa control and heater. Topside drops into a 1-3/4" round cutout in your spa. Intended for use under the redwood skirt of a typical portable spa, not out in the rain, snow, etc. -Runs a main 2 speed spa pump, and an air blower or 2nd pump, and spa light, and has a receptacle for ozonator or ionizer or any other non-switched device. -Comes with new power cords for your main 2-speed pump and an air blower or second pump, and a light, with quick disconnect plugs to the control.

-Optional purchase of extra cords not included can power an audio system, an additional device like a jet pump, and an ozonator, see our other listings for these optional cords. - Temperature sensor comes with a long cord so you can either mount the sensor onto the heater, or, mount it in your tub if your tub has a drywell, has provision for a remote temp sensor. Cord is 8 feet long, but again it is your choice to mount it right on the heater or stick the sensor into a tub fitting you already have. -Includes 15 inch long stainless steel high flow 2" heater, with 5kw Incoloy element. Can be used on 115/120v or 230/240 volts, it's changeable voltage-wise.

This is the common length of heater for 98% of hot tubs out there, comes with industry-standard black plastic split nuts with common buttress threads, so can couple right up to your existing plumbing if you have a 15" heater now. -the CBT7 can run off your 4-wire 230 volt supply voltage or off of a 3-wire 115 volt household power. Also, the pump and blower voltages can be changed to either 115/120v or 230/240v. On a 115/120 volt source, the heater will be 1.25kw or 1250 watts. From the factory the CBT7 is set for 230/240v incoming power, 230/240v to the heater, and 230/240v to the pumps.

115/120v to the air blower, and the ozonator, and 12 volts to the light. You can ask us and we can change voltages for you and test prior to shipping. Or, you can change the voltages yourself, it is easy. Can be mounted in any direction or position, even upside down, and the water can flow either direction through the heater. Can be fitted to 1-1/2" or 2" PVC pipe size systems -User's Manual shows how to program changes into the control, but it is factory programmed, and tested by United, and ready to go as is.

Nice unit, replaces most any existing spa control system, and is less costly than buying a new motherboard and topside in most cases. United Factory Warranty 12 months from date of manufacture against factory made defects, does not cover abuse, miswiring, lightning strikes, labor, freight, etc.. Control box stands 11.1" tall, and 15.5" wide, 3.4" deep, heater is 15" flange to flange. Designed, built and tested in the U.S. By United Spas, a rugged, proven, spa control, good tech support, good parts availability, made in California. Not refurbished, rebuilt, demo, all is brand new in factory packaging, warranted and backed by United Spas.

United has been building digital hot tub controls over 20 years. This goes out via ground shipping, to your street address, sorry, no P.O. Boxes. Shipping included is to LOWER 48 STATES ONLY. Questions? Please ask before you buy, please. Package includes: CBT7 Digital Control by United Spas model C5 15" stainless steel high flow 5kW heater with standard threaded couplings for 2" PVC plumbing.

Digital display keypad (topside) 2.5x5.0" with 9.5 foot long cord. Drops into 1-3/4" round cutout. One pump power cord 4-wire for a 2-speed pump, 45" long with quick disconnect AMP plug and motor connectors. 14/4 wire size. Air Blower power cord 57" with quick disconnect AMP plug, 18/3 wire size.

Light cord with quick disconnect AMP plug, 8 foot long. Temperature sensor and cord. United Spas t& Topside Installation Manual & User's Guide. United Spas C5 Series Installation & Service Manual. Additional info: Warranties: all warranties are from the manufacturers who made the goods, not from the distributors, dealers, or resellers.

Heater warranties do not cover running with air in the system (dry-fire) and burning a heating element, as this is not a defect. Pump warranties do not protect against seals being scratched by debris and leaking. Warranties do not cover freight costs. Standard stuff, but just fyi, so you are aware.