Canadian Spa Company Hot Tub Starter Kit - Essential Spa Water Chemicals

Canadian Spa Hot Tub Starter Kit For Hot Tubs, Pools & SpasYour spa is a source of relaxation and enjoyment practised throughout the ages. To get the most satisfaction out of your spa, the water must look clear, enticing and be free of bacteria. Three important factors contributing to this are filtration, water balance and disinfection.The perfect chemical kit for all portable and inflatable hot tubs. Easy to use, hassle free solution to maintaining your spa from day one. Each component ot the set comes with easy, simple to use instructions for use plus free Canadian Spa Water Test App on compatible smart phones.

Canadian Spa provides a dedicated, friendly UK customer support team to assist you with any queries you may have. What's In The Box: Chlorine Granules (500g) Directions For Use:1. Maintain recommended daily levels as determined by testing kit. Free available chlorine: 3.0-5.0 ppm; pH: 7.2-7.8; Total Alkalinity: 100-120 ppm; Calcium Hardness: 150-200 ppm. 2. Superchlorinate a freshly filled spa by adding 20g of chlorinating granules per 100l of spa water.

Maintain water circulation at least 15 minutes before using. Repeat superchlorination procedure after each use period. 3. Maintain proper chloring residual by adding daily, 10g of chlorinating graules per 1000l of spa water, or as needed. 4. Persistent foam formation, turbid or malodourous water are indicators of inadequate sanitizer levels. To correct such conditions, superchlorinate spa water by adding 30g per 1000l.

Maintain circulation at least 30 minutes and wait 4 hours before using. 5. Chlorinating Granules contain stabilizer (cyanuric acid) which will accumumlate in spa water. Keep stabilizer within the 30-100 ppm range by dilution with fresh water. 6. For proper sanitation, spa must be completely drained periodically. The number of days between COMPLETE SPA DRAINAGE is equal to the volume of spa water in litres, divided by 10 times the maximum number of daily spa users.

Refill spa with water and repeat DIRECTIONS FOR USE. 7. Maximum spa water usage temperature is 40ºC. Duration in spa water at 40ºC should not exceed 15 minutes. PH UP (500g) Proper pH balance is an essential part of spa/hot tub maintenance. The recommended range is 7.2 to 7.6.

If the pH of your spa/hot tub is low (below 7.2) the water will be acidic. Discomfort from skin and eye irritation could develop. This condition also causes chlorine to become unstable, and therefore less effective in killing bacteria, algae and in disintegrating organic matter. Test water daily for pH and bromine/chlorine levels. When test readings indicate a pH below 7.2 follow the instructions on the bottle.

PH Down (500g) Proper pH balance is an esstial part of spa/hot tub maintenance. The recommended range is 7.2 to 7.6. If the pH of your spa/hot tub is high (above 7.6), the water will alkaline and the chlorine is prevented from doing its job since it "combines' with other materials in the pool water. The existence of this phenomenon is usually detected by a strong chlorine odour not found when the pH is in balance. The water tends to be cloudy and eye irritation may develop.

Scale build-up may also begin to occur. Test water daily for pH and bromine/chlorine. When pH reading is above 8.0 add 60g of pH Down per 1000 litres of water. If pH reading is 7.8-8.0 add 30g of pH Down per 1000 litres directly to the spa/hot tub. Let water circulate for 1 hour and test again.

Foam Free (500ml) Eliminates and prevents foaming. Just a small dose of this product quickly breaks down bio-oils and impurities that cause foaming. Use Canadian Spa Foam Free to eliminate pollutants (soaps and creams) from foaming in your spa/hot tub by sinking them and taking them to the filter. Simply shake well and squirt where foam is forming to reduce and remove unsightly bubbles without having to drain and refill your spa/hot tub. Use in moderation as needed.

Test Strips (50) Each strip tests: Free chlorine - pH - Total Alkalinity. A test for the most important water parameters in your pool or spa. Directions For Use: 1. Dip a test strip in water for 5 seconds, moving it gently back and forth. 2. Remove strip.

Shake once to remove drops of water. 3. Wait 15 seconds. 4. Compare the test pads with colour chart on the bottle within the next 30 seconds. NOTE: A 10 second dip time is necessary if the water temperature is below 75ºF / 23ºC. Download Our Free Mobile Water Test APP at the APP Store or Google Play